ALYA AKRİLİK GRENLİ DIŞ CEPHE BOYASI
DEFINITION
It is a textured, matte-looking, top coat exterior paint based on styrene acrylic copolymer binder and silicone emulsion, which does not lose its flexibility between -40 °C and +60 °C, provides its surface hardness by cross-linking with UV rays, is applied with a roller, patterned with a roller, and has a matt appearance.
-Photoroom.jpg)
FEATURES
It has high alkali resistance. It is extremely resistant to sunlight, rain and moisture. It is used as a final coat exterior paint that covers capillary cracks that may arise from shrinkage in concrete and plasters with its elastomeric and textured properties.
It is applied on the exterior facades of buildings, on mineral surfaces such as concrete, plaster, brick, eternit, etc.
25 Kilogram / Plastik Kova
SARFİYAT:
Uygulama yapılacak yüzeyin cinsine, emiciliğine ve yapısına göre 1 Kilogram ile tek katta 0,8-1 m² alan boyanabilir. Kesin sarfiyat için kontrollü numune çalışması yapılmalıdır.
KURUMA SÜRESİ (20°C, %65 Bağıl Nemde)
Dokunma kuruması: 3-4 saat
Son kuruma: 24 saat (daha yüksek bağıl nem ve düşük sıcaklıkta kuruma süresi uzayabilir).
It can be stored for 3 years in its unopened packaging, in a cool and dry place, protected from frost and direct sunlight. Close the lid of the packaging immediately after use in an airtight manner.
R 43: May cause sensitization by skin contact.
S 2: Keep out of reach of children.
S 23: Do not breathe vapour.
S 24/25: Avoid contact with eyes and skin.
S 37: Wear suitable gloves.
S 46: If swallowed, seek medical advice immediately and show the container or label.
S 56: Dispose of this material and its container to hazardous or special waste collection point.APPLICATION
Swollen, loosened, old paints are scraped off. Cracks are filled with putty. It is recommended to apply 1 layer of Binder or Colored Primer without diluting to strengthen the prepared surfaces, to bond free micronized powders, to reduce the absorbency of the surface, paint consumption and to increase adherence. The waiting period after the primer coat application is approximately 6-12 hours depending on the ambient conditions. Silicone Grained Exterior Wall Coating should be mixed until it reaches a homogeneous consistency. It should be spread on the entire surface with a lambskin roller in equal thickness. While the Silicone Grained Exterior Wall Coating is still wet, a pattern should be applied from top to bottom with a coral roller. The coral roller should be saturated with the material before application. In order not to spoil the pattern, care should be taken not to overfill the roller or dry it. Lambskin roller can also be used for a different pattern. The thickness or thinness of the pattern can be adjusted by adding water. However, excessive water may cause the pattern to run and disappear, differences in covering and late drying depending on the season. Adhesive tapes should be removed carefully before the Silicone-Based Grainy Exterior Coating hardens.In high-volume painting works to be done on exterior facades, it is important to pay attention to purchasing the products from the same batch in order to prevent tone differences. At least 15 liters of paint should be separated for touch-up operations and care should be taken to ensure that the dilution to be done in the touch-up process is the same as in the first application. Since drying will be quick in windy and hot weather, areas that can be finished in one stage should be selected, taped and serially applied without interruption in order to avoid joints on large surfaces.
THINNING
In brush and roller applications, it is recommended to dilute it with clean water by a maximum of 15% and apply it in two coats. In high-volume exterior painting jobs, care should be taken to dilute the products at the same rate to avoid tone differences.